www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 1 of 8 spec no : ? ? s s p p e e c c i i f f i i c c a a t t i i o o n n customer product ? saw filter model no ? hdf109a2 smd-3 marking ? ? hdf119 prepared ? checked ? approved ? d a t e ? 2009-8-3 ??? shoulder electronics limited ?? customer received: checked ? approved date
saw filter hdf109a2 s3 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 2 of 8 ?? history record date spec. no. ?? part no. ??? customer no. modify content ? remark
saw filter hdf109a2 s3 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 3 of 8 1. scope this specification shall cover th e characteristics of saw filter with f109a2 used for the page system. 2. electrical specification dc voltage vdc 0v ac voltage vpp 10v50hz/60hz operation temperature -40 to +85 storage temperature -45 to +85 rf power dissipation 0dbm electronic characteristics 2-1.typical frequency response
saw filter hdf109a2 s3 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 4 of 8 2-2.electrical characteristics ? part number HDF109A2S3 ? (fo)(mhz) nominal center frequency 109.35 1db 1db bandwidth 600min 3db 3db bandwidth(from fo)(khz) 700min ? stop band attenuation (from peak level)(db) 1)5.00~103.70mhz 2)115.00~200.00mhz 55min 45min (db) insertion loss(at minimum loss point) 4.5max vswr (at passband of 1.0 mhz) with the matching network 1.6 ?? (fo+/-50khz)( nsec.) group delay variation 60 ?? (fo+/-500khz)( sce.) absolute group delay 1.2max ?? (fo+/-50khz)( sce.) absolute group delay 0.85max / input/output impedance 200 ?8pf 3.test circuit c1=c2=11pf l1=l2=68nh
saw filter hdf109a2 s3 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 5 of 8 4. dimension marking hdf119 hd: brand f : filter 119 : no. 5. environmental characteristics 5-1 temperature cycling subject the device to a low temperature of -40 for 30 minutes. following by a high temperature of +25 for 5 minutes and a higher temperature of +85 for 30 minutes. then release the device into the room conditions for 1 to 2 hours prior to the measurement. it shall meet the specifications in 2-2. 5-2 resistance to solder heat submerge the device terminals into the solder bath at 260 5 for 10 1 sec. then release the device into the room conditions for 4 hours. it shall meet the specifications in 2-2. 5-3 solderability submerge the device terminals into the solder bath at 245 5 for 5s, more than 95% area of the soldering pad must be cove red with new solder. it shall meet the specifications in 2-2. 5-4 mechanical shock drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 2-2. 5-5 vibration subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. the f ilter shall fulfill the specifications in 2-2. 2.input 6. output 1.3.5.7:ground 4.8 ground
saw filter hdf109a2 s3 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 6 of 8 6. remark 6.1 static voltage static voltage between signal load & gr ound may cause deterioration &destruction of the component. please avoid static voltage. 6.2 ultrasonic cleaning ultrasonic vibration may cause deterioratio n & destruction of the component. please avoid ultrasonic cleaning 6.3 soldering only leads of component may be solder ed. please avoid soldering another part of component. 7. packing 7.1 dimensions (1) carrier tape: figure 1 (2) reel: figure 2 (3) the product shall be packed properly not to be damaged during trans portation and storage. 7.2 reeling quantity 1000 pcs/reel 7?? 3000 pcs/reel 13?? 7.3 taping structure (1) the tape shall be wound around th e reel in the direction shown below. (2) label device name
saw filter hdf109a2 s3 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 7 of 8 user product name quantity lot no. (3) leader part and vaca nt position specifications. 8. tape specifications 8.1 tensile strength of ca rrier tape: 4.4n/mm width 8.2 top cover tape adhesion (see the below figure) (1) pull off angle: 0~15 o (2) speed: 300mm/min. (3) force: 20~70g [figure 1] carrier tape dimensions
saw filter hdf109a2 s3 www.shoulder.cn tel:0755-82916880 fax:0755-82916881 e-mail:info@shoulder.cn page 8 of 8 [unit:mm] w f e p0 p1 p2 d0 d1 t1 t2 a b 12.0 0.3 5.5 0.05 1.75 0.1 4.0 0.1 8.0 0.1 2.0 0.05 ?1.5 0.1 ?1.0 0.25 0.3 0.05 2.10 0.1 6.40 0.1 5.20 0.1 [figure 2] [unit:mm] a b c d e w t r ? 330 1.0 ? 100 0.5 ? 13 0.5 ? 21 0.8 2 0.5 13 0.3 3 max. 1.0 max.
|
